WELDED BLOCK PLATE HEAT EXCHANGERSProcess heating · Cooling · Condensation · Heat recovery
COMPABLOC REPLACEMENT

Compabloc CP50 Core & Complete-Unit Replacement

Assess replacement of an existing Compabloc CP50 using its nameplate, drawings and process duty. Compare a replacement welded core with a complete HEXCBLOC 50 unit; the model reference is a starting point for engineering review.

ParameterALFA LAVAL
Compabloc CP50
PANSTAR
HEXCBLOC 50
Maximum width840 mm840 mm
Maximum height2,050 mm2,050 mm
Published design pressureASME maximum: 38 barStandard: full vacuum to 32 bar
Published temperature range−46 °C → 343 °C−40 °C → 300 °C
ConstructionWelded plate pack; removable panelsWelded plate pack; removable panels
Core / plate packCompabloc CP50Replacement core available following drawing and configuration review

Published reference dimensions and ratings describe standard ranges. Verify the actual installed unit nameplate and drawing. Plate count, materials, nozzles and baffles determine the supplied configuration; the references do not establish interchangeability.

Replacement Paths for an Existing CP50

Option A: Welded core / plate pack replacement

Consider a new welded core if selected existing casing components can be retained. Establish the retained parts, inspect their condition and verify the internal interfaces before confirming feasibility. Core supply does not automatically include replacement panels, seals or bolts.

Option B: Complete-unit replacement

Consider a complete exchanger when casing condition, a changed duty or interface constraints make core-only work unsuitable. Define the piping, support and installation changes included in the proposal. Neither route is confirmed from the CP50 designation alone.

What Must Match for a Core Replacement?

Review the retained casing condition and measured internal core envelope against the proposed plate-pack width, height and depth. Check header / nozzle connections, panel and seal faces, baffle arrangement, internal supports and the tie-bolt / cover interface where relevant. The external width in the comparison table is not the internal core dimension.

Confirm plate and seal materials for both fluids, design pressure and temperature, service duty and cleaning access. Identify dimensional discrepancies or worn parts before defining the replacement geometry. Plate Pack Replacement Engineering explains the detailed inspection and interface assessment; matching an OEM internal profile is not assumed.

What Must Match for a Complete-Unit Replacement?

Compare overall dimensions, nozzle sizes and positions, orientation, flange standard and connection centre lines with the installed CP50 drawing. Review foundation and support interfaces, lifting access, the route into the plant and maintenance clearance for removable panels.

Recheck thermal duty, flow range, allowable pressure drop, materials and design conditions for the proposed complete assembly. Similar published dimensions do not confirm nozzle alignment or identical ratings. State any piping or foundation modifications and site-work responsibilities before ordering.

What PANSTAR Needs to Review a CP50

  • Identify the unit: CP50 nameplate, model and serial number if available, original datasheet, GA drawing, photographs and reason for replacement.
  • Define the duty: hot- and cold-side fluids, flow rates, inlet / outlet temperatures, operating pressure and allowable pressure drop on each side.
  • Confirm the design basis: design pressure, design temperature, plate material and panel / seal materials if known.
  • Measure the installation: existing dimensions, nozzle sizes and positions, supports and access constraints; add internal measurements for core-only assessment.

Not all information is required for the first inquiry. Send what is available. Identify missing drawings or uncertain measurements so the next review step can be agreed.

Replacement Decision Checklist

  • Thermal match: agreed duty and hydraulic limits for the operating range.
  • Mechanical fit: core envelope or complete-unit dimensions checked against drawings.
  • Pressure boundary and materials: complete assembly, design conditions and wetted materials reviewed.
  • Nozzle alignment and support / footprint: connections, foundation and required modifications identified.
  • Service access: lifting, panel removal and cleaning clearance available.
  • Documentation and retained parts: drawing revisions, inspection findings and reuse decisions recorded.

Alfa Laval Compabloc · 200000002-1-EN-GB · HEXCBLOC 50 · Published specifications

Alfa Laval and Compabloc identify the original equipment. HEXCBLOC is supplied by PANSTAR.

Compare another Compabloc model

Send Your CP50 Nameplate & Drawings

Send the available nameplate, datasheet, drawings and photographs. State the current problem and preferred replacement scope; PANSTAR will review the information needed for the next assessment step.

Request CP50 Replacement Assessment